|
Curvadora Desde 180 hasta 500
Medios de pagos disponibles: |
Especificaciones Técnicas:
Model Barletta | 180 | 200 | 260 | 320 | 400 | 500 | |
Max. Section Modulus | 180 cm3 | 200 cm3 | 260 cm3 | 320 cm3 | 400 cm3 | 500 cm3 | |
Angle leg-out
|
Max. cross section(㎜) | 150x150x16 | 160x160x16 | 160x160x20 | 180x180x20 | 200x200x18 | 250x250x25 |
Max. bending diameter(㎜) | 2400 | 2000 | 3000 | 3200 | 3500 | 4000 | |
Angle leg-in
|
Max. cross section (mm) | 150x150x16 | 160x160x16 | 160x160x20 | 170x170x20 | 180x180x16 | 200x200x25 |
Min. bending diameter (mm) | 2600 | 2400 | 3000 | 3200 | 4000 | 400 | |
Flat-along face
|
Max. cross section (mm) | 160x40 | 150x60 | 160x60 | 180x60 | 200x60 | 200x60 |
Min. bending diameter (mm) | 2000 | 1400 | 2000 | 2500 | 3000 | 3000 | |
Flat-along edge
|
Max. cross section (mm) | 300x50 | 280x50 | 350x50 | 350x60 | 400x70 | 500x70 |
Min. bending diameter (mm) | 1800 | 1200 | 2200 | 2400 | 2500 | 2500 | |
U-beam leg-out
|
U-beam model | 32 | 30 | 36 | 36 | 40 | 50 |
Min. bending diameter (mm) | 3000 | 2300 | 2000 | 3000 | 4000 | 5000 | |
U-beam leg-in
|
U-beam model | 32 | 30 | 30 | 30 | 40 | 50 |
Min. bending diameter (mm) | 3500 | 2500 | 2500 | 4000 | 5000 | 6000 | |
Solid bar
|
Diameter (mm) | Ø 120 | Ø130 | Ø140 | Ø150 | Ø160 | Ø180 |
Min. bending diameter (mm) | 2400 | 2400 | 2500 | 2500 | 2500 | 3000 | |
Pipe
|
Diameter x pipe thickness (mm) | Ø 130x10 | Ø140x10 | Ø159x10 | Ø168x10 | Ø245x10 | Ø300x10 |
Min. bending diameter (mm) | 2500 | 3000 | 3500 | 4000 | 5000 | 6000 | |
T-beam
|
Width(height) x thickness | 150x12 | 150x14 | 160x14 | 170x14 | 186x16 | 200x16 |
Min. bending diameter (mm) | 2600 | 3000 | 3500 | 4000 | 5000 | 600 | |
I-beam
|
I-beam model | 22 | 22 | 30 | 35 | 40 | 45 |
Min. bending diameter (mm) | 2600 | 4000 | 4000 | 4500 | 5000 | 600 | |
Square
|
Width x thickness | 140x10 | 145x8 | 150x10 | 165x10 | 180x12 | 200x12 |
Min. bending diameter (mm) | 3000 | 3000 | 3500 | 3500 | 3500 | 4000 | |
Rectangular
|
Length x width x thickness | 140x80x6 | 160x50x6 | 160x80x8 | 180x90x8 | 200x100x10 | 200x120x10 |
Min. bending diameter (mm) | 3000 | 3000 | 3200 | 3500 | 4000 | 450 | |
Bending Speed | 5m/min | ||||||
Hydraulic pressure | 20MPa | ||||||
Main motor power | 15KW | 15KW | 22KW | 30KW | 37KW | 45KW |